Realtime GPS/GSM/GPRS Tracking System Tracker Device

GSM/GPRS/GPS Tracker working based in existing GSM/GPRS network and GPS satellites,this product can locate and moniter any remote targets by SMS or internet.

This GPS tracker can be used to determine the precise location of a vehicle, person, or other asset to which it is attached and to record the position of the asset at certain intervals. This is an advanced GPS satellite positioning system tracker with precise tracking of an object anywhere in the world, works on all available GSM/GPRS mobile networks 850/900/1800/1900MHZ.It can reponse latitude and longitude information to your mobile phone by SMS. Get it today to prevent your car, children and asset from getting stolen or lost,etc...

Applications

• Vehicel rental/Fleet management etc
• Protect child/the old/the disabled/pet etc
• Provide peace-of-mind for businessmen
• Manage personal
• Track criminals cretly

Specifecations

Usage:

1.SIM Card installation

Make sure that there is no call transfer and call display is on, and PIN code off. The SMS message must in Text format, can’t be identified for PDU format.

Steps:

1 Open the rear cover, and pick out the battery.

2 Push the foil along and turn it left.

3 Put the SIM card into the holder, and turn the foil right and fasten it in

2. Battery and Charger

Do charge the battery to capacity in 8 -12 hours for first use. Please use the battery and charger provided by the manufacturer. This unit adopts built-in Li-ion battery, and full battery will support around 48 hours use on end. After first use, the battery can be charged fully in 3-5hours.

3.Startup

Put the SIM card and battery in place.

Turn on the unit outdoors by pressing the “on/off” button until the indicator is on.

For first use, please initialize the unit and restore it to default setting.( please refer to 5.4 for instruction.)

In 10 or 40seconds, the unit will begin to work and acquire the GSM signals as well as the GPS signals. The indicator will keep flashing every 4 seconds when the unit has received the signals, otherwise it will keep on.

When this unit receives GPS signals normally, you can use it and do all the following settings.

4. Initialization

Send “begin+password” in SMS to the unit, it will reply “begin ok” and initialize all the settings. (default password: 123456)

5. Change the password

Send SMS password+old password+space+new password to change the password.

Remark:

5.1 Be sure keep the new password in mind.

5.2 Make sure the new password is in 6 digits, or else the tracker can not recognize the password.

6.Authorization

There are only 5 numbers able to be authorized.

6.1 Call the tracker for 10 times, it will make the cell phone number as the authorized number automatically.

6.2 Send SMS admin+password+space+cell phone number to set up a authorized number. The other authorized numbers should be set by the first authorized number. If the number is successfully authorized, the unit will reply “admin ok!” in SMS.

6.3 Send SMS noadmin+password+space+authorized number to delete the authorized number.

6.4 For roaming purpose, you have to add your country code ahead of the cell phone number, for example, please send admin123456 008613322221111 to tracker to set 13322221111 as an authorized number.

7. Real-time polling

7.1 If there is no authorized number, when any number dials up the unit, it will report a Geo-info; If there is already an authorized number, then it will not respond when an unauthorized number calls it up.

7.2 When an authorized number dials up the unit, it will hang up and report a real-time Geo-info;

8. Auto Track

Report a Geo-info at 30s intervals to the authorized numbers for 5 times:

8.1 Set up: Send SMS t030s005n+password to the unit, it will report the Geo-info at 30s intervals for 5 times.(s: second, m: minute, h: hour). The setting must be in 3 digits and at maximum 255 in value.

8.2 Send SMS t030s***n+password to the unit, it will reply SMS heaps of times

8.3 Cancel: Send notn+password to delete the “ auto track ”

Remark: the interval must not be less than 20s.

9. Voice Surveillance

In this mode, the user can dial up the unit to monitor the voice (please refer to 5.10 for instruction).

10. Modes switch between “track” and “monitor”

10.1. The default mode is “track”.

10.2. Send SMS monitor+password to the unit, and it will reply “monitor ok!” and switch to “monitor”mode.

10.3. Send SMS tracker+password to the unit, it will reply “tracker ok!” and restore to “track” mode.

11. Geo-fence

Set up a geo-fence for the unit to restrict its movements within a district. The unit will send the message to the authorized numbers when it breaches the district.

11.1 Set up: When the unit stays immobile in a place for 3-10 minutes, the user can Send SMS stockade+password+space+latitude,longitude; latitude,longitude to unit to set the restricted district. In case of breach, it will send SMS “stockade!+geo-info” to the authorized numbers.

Remark : The first latitude&longitude is coordinate of the top left corner of the Geo-fence, while the second latitude&longitude is the coordinate of the bottom right corner. It will alarm one time in each setting.

11.2 Cancel: Send SMS nostockade+password to deactivate this function.

This function will be out of effect after the unit moves outside the district.

12. Movement alert

12.1 Set up: When the unit stays immobile in a place for 3-10 minutes, the user can send SMS move+password to the unit, then the unit will reply “move ok!”. In case of such a movement, it will send SMS “Move” along with a Geo-info to the authorized numbers. It will alarm one time in each setting.

12.2 Cancel: Send SMS nomove+password to deactivate the movement alert.

Remark: This function will be out of effect after the unit moves outside the district.

13. Overspeed alert:

13.1 Set up: Send SMS speed+password+space+080 to the unit (suppose the speed is 80km/h), and it will reply “speed ok!”. When the target moves exceeding 80 km/h, the unit will send SMS speed+080!+Geo-info to the authorized numbers. It will alarm one time in each setting.

13.2 Cancel: Send SMS nospeed+password to deactivate the overspeed alert

Remark: It is recommended that the speed alarm is set at not less than 50km/h. For below that rate, it may cause the excursion of the GPS signal influenced by clounds etc.

Any questions please feel free to contact us.